Guides for Camberley homeowners
Painted or wood finish: choosing how your fitted furniture looks
The finish is the part of fitted furniture you see and touch every day. It also decides how the piece copes with knocks, sunlight and sticky fingers.
There are really four choices. Two are paint and two are wood. Here is what each one is like to live with.
Sprayed paint
The doors and panels are painted with a spray gun, usually in a workshop before fitting. The result is perfectly flat, with no brush marks, and the paint used is typically a hard lacquer.
It suits modern, plain designs and handle-free doors, where any flaw in the surface would show. It wears well and wipes clean.
The drawback is repair. A deep chip cannot simply be touched in with a brush without the patch showing. A damaged door usually goes back to be resprayed. Ask the carpenter for a small pot of the exact colour all the same, for minor marks.
Hand-painted
The furniture is primed, fitted, then painted in the room with a brush and small roller. You get a faint brush texture that many people prefer on panelled and traditional designs.
Its great advantage is that it can be repaired and changed. A scuff is touched in. In ten years, when you are tired of the colour, the whole piece can be repainted like any other woodwork.
It takes longer on site, and the room is out of use while coats dry. The quality depends heavily on preparation, so ask who is painting and how many coats they allow. The alcove cupboards cost guide gives a rough figure of £15 a square metre for painting woodwork.
Wood veneer on board
A thin layer of real oak, walnut or ash is bonded to a stable board. It is real timber on the surface, with real grain, and it is finished with oil or clear lacquer.
Because the board underneath does not move much, veneered panels stay flat on wide doors and long shelves. This is what most oak-look fitted furniture is made from, and done well it is very handsome.
The veneer is thin. It can be lightly sanded once or twice in its life, not repeatedly. Exposed edges need a matching timber lipping, or they give the game away. Look at the edges in a carpenter's photos.
Solid timber
Solid oak or another hardwood right through. It is used for desk tops, shelf fronts, door frames and handrails, and sometimes for whole pieces.
It feels the best and can be sanded and refinished many times. It also costs the most and moves with the seasons, swelling a little in damp months and shrinking in dry ones. A good maker allows for that in the design. Wide solid panels are usually avoided for doors for this reason.
What is under the paint
Painted furniture is nearly always MDF, and that is a good thing. MDF is flat, stable and has no grain to show through. For doors and visible panels, a moisture-resistant grade takes paint better on its cut edges.
For carcasses, the hidden boxes, carpenters use MDF, plywood or a melamine-faced board that needs no painting inside. Plywood is stronger and holds screws better. Melamine gives a wipe-clean interior straight away. Any of them is fine if it is thick enough for the span.
Mixing finishes
Some of the best-looking pieces use two. Painted cupboards with an oak top. A painted wardrobe with oak-veneered shelves and drawer fronts inside. A fitted desk with a solid oak worktop on painted drawers.
The wood goes where your hands and eyes land. The paint goes everywhere else and ties the piece to the room's other woodwork.
- Lounge alcoves: painted, often with an oak or painted top. See alcove units.
- Wardrobes: sprayed or hand-painted doors, with melamine or veneer inside. See fitted wardrobes.
- A study: painted cupboards with a hard-wearing wood or laminate top. See fitted home offices.
- Stairs: painted spindles and strings with an oak handrail. See staircase renovation.
Colour, light and the rest of the room
Ask for a painted sample board and stand it in the room for a few days. A colour shifts between a north-facing bedroom and a south-facing lounge, and between morning and lamplight.
Matching the furniture to the skirting and door frames makes it recede. A contrasting colour makes it a feature. Either is a fair choice. Just make it on purpose.
Common questions
Which finish is most hard-wearing?
A sprayed lacquer is the toughest painted surface, and a lacquered veneer the toughest wood one. For a family house with young children, think about repair as much as toughness. A hand-painted finish marks more easily but is the simplest to put right.
Can fitted furniture be repainted later?
Yes. Hand-painted pieces repaint easily. Sprayed pieces can be repainted by brush after a light sanding, though the look changes from sprayed to brushed. Veneered pieces can be re-oiled or re-lacquered, and painted over if you really want a change.
Choose the finish before the price
The finish changes the cost of a piece more than almost anything else, so two quotes mean nothing side by side unless both are for the same one. Deciding first saves a round of confusion.
Say which finish you lean towards when you describe the job, and add your area.